HPTouchPad:Installing CM-9 - Revision history

Avni: /* Reboot and Install */

2014-06-13T03:17:53Z

Reboot and Install

← Older revision		Revision as of 20:17, 12 June 2014
Line 34:		Line 34:
	===Reboot and Install===		===Reboot and Install===
	Reboot the TouchPad into USB (recovery) mode		Reboot the TouchPad into USB (recovery) mode
			* Shutdown the tablet
	* Hold PowerOn button and Volume UP simultaneously until the large white USB symbol appears on the TouchPad display.		* Hold PowerOn button and Volume UP simultaneously until the large white USB symbol appears on the TouchPad display.
	* Connect TouchPad to PC with provided USB cable. The PC will give a tone indicating the connection is made.		* Connect TouchPad to PC with provided USB cable. The PC will give a tone indicating the connection is made.

BillM at 00:54, 1 July 2013

2013-07-01T00:54:12Z

← Older revision		Revision as of 17:54, 30 June 2013
Line 28:		Line 28:
	* Create a directory <code>clockworkmod</code> in the webOS root directory.		* Create a directory <code>clockworkmod</code> in the webOS root directory.
	* Create a directory <code>backup</code> in the newly created <code>/clockworkmod</code> directory		* Create a directory <code>backup</code> in the newly created <code>/clockworkmod</code> directory
	* Copy the ~~correct~~ archive to the <code>/clockworkmod/backup</code> directory.		* Copy the CM-9 configuration archive files to the <code>/clockworkmod/backup</code> directory. There should be only one directory under <code>/clockworkmod/backup</code> and it should be named <code>2013-05-16.15.13.12/</code>.

	Eject the TouchPad, then disconnect the USB cable from the TouchPad		Eject the TouchPad, then disconnect the USB cable from the TouchPad

BillM at 22:31, 20 June 2013

2013-06-20T22:31:14Z

← Older revision		Revision as of 15:31, 20 June 2013
Line 3:		Line 3:

	This page describes how to install CyanogenMod 9 onto an HP TouchPad. It refers to file and directory names found in the previous step: [[HPTouchPad:Configuring webOS\|Configuring webOS]].		This page describes how to install CyanogenMod 9 onto an HP TouchPad. It refers to file and directory names found in the previous step: [[HPTouchPad:Configuring webOS\|Configuring webOS]].

			===Assumptions===
			These steps are dependent on the host system being properly set up with the correct files. All steps specified in [[HPTouchPad:PC Setup\|PC Setup]] should be complete before starting here.

	===Prepare the TouchPad===		===Prepare the TouchPad===

BillM at 21:42, 20 June 2013

2013-06-20T21:42:34Z

← Older revision		Revision as of 14:42, 20 June 2013
Line 46:		Line 46:
	Moboot should present multiple boot selections, and it should default to CyanogenMod 9 after a timeout of about five seconds. Allow the TouchPad to boot to CM-9. It takes two or more minutes to reboot.		Moboot should present multiple boot selections, and it should default to CyanogenMod 9 after a timeout of about five seconds. Allow the TouchPad to boot to CM-9. It takes two or more minutes to reboot.

	Proceed to configure the CM-9 environment.		Proceed [[HPTouchPad:Configuring CM-9\|to configure the CM-9 environment]].

BillM: Created page with "''Last Updated:''' {{REVISIONMONTH}}/{{REVISIONDAY2}}/{{REVISIONYEAR}} '''By:''' {{REVISIONUSER}} This page describes how to install CyanogenMod 9 onto an HP TouchPad. It refer..."

2013-06-20T21:26:51Z

Created page with "''Last Updated:''' {{REVISIONMONTH}}/{{REVISIONDAY2}}/{{REVISIONYEAR}} '''By:''' {{REVISIONUSER}} This page describes how to install CyanogenMod 9 onto an HP TouchPad. It refer..."

New page

''Last Updated:''' {{REVISIONMONTH}}/{{REVISIONDAY2}}/{{REVISIONYEAR}}
'''By:''' {{REVISIONUSER}}

This page describes how to install CyanogenMod 9 onto an HP TouchPad. It refers to file and directory names found in the previous step: [[HPTouchPad:Configuring webOS|Configuring webOS]].

===Prepare the TouchPad===
*Boot the TouchPad to webOS.
*Connect the TouchPad to the PC with the provided USB cable.
*A USB notification window will pop up on the TouchPad display.
*Select USB Drive mode.
*The TouchPad will be assigned a device drive number by Windows Explorer.
*Windows Explorer will create a window open to the TouchPad's root directory.

====Create the install directory====
Create a directory <code>cminstall</code> in the webOS root directory. Precise spelling and case is essential.

Copy the four .zip files from the PC's <code>cminstall.dir</code> folder into the TouchPad <code>/cminstall</code> directory:
<tt>
*moboot_038-tenderloin
*cm-9-20130429-NIGHTLY-tenderloin
*update-CWM6_tenderloin-20121215
*update-gapps-ics-20120429-signed</tt>

====Create the backup recovery directory====
* Create a directory <code>clockworkmod</code> in the webOS root directory.
* Create a directory <code>backup</code> in the newly created <code>/clockworkmod</code> directory
* Copy the correct archive to the <code>/clockworkmod/backup</code> directory.

Eject the TouchPad, then disconnect the USB cable from the TouchPad

===Reboot and Install===
Reboot the TouchPad into USB (recovery) mode
* Hold PowerOn button and Volume UP simultaneously until the large white USB symbol appears on the TouchPad display.
* Connect TouchPad to PC with provided USB cable. The PC will give a tone indicating the connection is made.

On the PC, open a Windows Command execution window
* <code>cd C:\Program Files\Palm, Inc</code>
* Excute the following command:
** <code>novacom boot mem:// < ACMEInstaller3</code>
* The prompt will return within a second or two.
* The TouchPad display will change to the HP logo and then immediately to the Double Penguin display mode.
* Screens of text will scroll by while the installation proceeds.
* The TouchPad will reboot in five minutes or so.
* Disconnect the TouchPad from the PC as it boots.

Moboot should present multiple boot selections, and it should default to CyanogenMod 9 after a timeout of about five seconds. Allow the TouchPad to boot to CM-9. It takes two or more minutes to reboot.

Proceed to configure the CM-9 environment.